Roundup, Pro Max, 1.67 gal
- Non-selective post-emergent herbicide
- Unique surfactant system gets to the roots faster
$159.99
Your pick up store is Pasco
5 in stock
Roundup Pro Max is a non-selective post-emergent herbicide that controls a broad spectrum of weeds with virtually no re-growth. Roundup Pro Max has a unique surfactant system that’s more concentrated and gets to the root faster, so you don’t have to worry so much about the weather and rain washing the product away. For this product to be effective, make sure that weeds have emerged at the time of application. This product comes in a 1.67-gallon jug with a 6 ½ fluid oz measuring cup.
This item cannot be sold in the following states: California, California
| Dimensions | 6.64 × 9.6 × 11.83 in |
|---|
ATTENTION:
This specimen label is provided for general information only.
-
This pesticide product may not yet be available or approved for sale or use in your area.
-
It is your responsibility to follow all Federal, state and local laws and regulations regarding the use of pesticides.
-
Before using any pesticide, be sure the intended use is approved in your state or locality.
-
Your state or locality may require additional precautions and instructions for use of this product that are not included here.
-
Monsanto does not guarantee the completeness or accuracy of this specimen label. The information found in this label may differ from the information found on the
product label. You must have the EPA approved labeling with you at the time of use and must read and follow all label directions.
-
You should not base any use of a similar product on the precautions, instructions for use or other information you find here.
-
Always follow the precautions and instructions for use on the label of the pesticide you are using.
Complete Directions for Use
AVOID CONTACT OF HERBICIDE WITH FOLIAGE, STEMS, EXPOSED NON-WOODY ROOTS OR FRUIT OF CROPS, DESIRABLE PLANTS AND TREES, BECAUSE SEVERE INJURY OR DESTRUCTION IS LIKELY TO RESULT.
EPA Reg. No. 524-579
Read the entire label before using this product. Use only according to label instructions.
2010-1
Not all products listed on this label are registered for use in California. Check the registration status of each product in California before using.
Read the LIMIT OF WARRANTY AND LIABILITY statement at the end of the label before buying or using. If terms are not acceptable, return at once unopened.
THIS IS AN END-USE PRODUCT. MONSANTO DOES NOT INTEND AND HAS NOT REGISTERED IT FOR REFORMULATION OR REPACKAGING.
PRODUCT INFORMATION 1.0 INGREDIENTS
ACTIVE INGREDIENT:
*Glyphosate, N-(phosphonomethyl)glycine,
in the form of its potassium salt...................................................................... 48.7% OTHER INGREDIENTS:........................................................................................ 51.3% 100.0%
*Contains 660 grams per liter or 5.5 pounds per U.S. gallon of the active ingredient glyphosate, in the form of its potassium salt. Equivalent to 540 grams per liter or 4.5 pounds per U.S. gallon of the acid, glyphosate.
This product is protected by U.S. Patent No’s. 5,668,085 and 6,365,551. Other patents pending. No license granted under any non-U.S. patent(s).
2.0 IMPORTANT PHONE NUMBERS
FOR PRODUCT INFORMATION OR ASSISTANCE IN USING THIS PRODUCT,
CALL TOLL-FREE, 1-800-332-3111.
3.0 PRECAUTIONARY STATEMENTS 3.1 Hazards to Humans and Domestic
Animals
Keep out of reach of children.
CAUTION!
CAUSES MODERATE EYE IRRITATION.
Avoid contact with eyes or clothing. Avoid breathing vapor or spray mist.
FIRST AID: Call a poison control center or doctor for treatment advice.
IF IN EYES
• Hold eye open and rinse slowly and gently with water for 15 to 20 minutes.
• Remove contact lenses if present after the first 5 minutes then continue rinsing eye.
-
Have the product container or label with you when calling a poison control center or doctor, or going for treatment.
-
You may also contact (314) 694-4000, collect day or night, for emergency medical treatment information.
-
DOMESTIC ANIMALS: This product is considered to be relatively nontoxic to dogs and other domestic animals; however, ingestion of this product or large amounts of freshly sprayed vegetation may result in temporary gastrointestinal irritation (vomiting, diarrhea, colic, etc.). If such symptoms are observed, provide the animal with plenty of fluids to prevent dehydration. Call a veterinarian if symptoms persist for more than 24 hours.
Personal Protective Equipment (PPE)
Applicators and other handlers must wear: long-sleeved shirt and long pants, shoes plus socks.
Follow manufacturer’s instructions for cleaning/maintaining PPE. If there are no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry.
When handlers use closed systems, enclosed cabs, or aircraft in a manner that meets the requirements listed in Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS.
-
User Safety Recommendations
Users should:
• Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet.
• Remove clothing immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing.
-
3.2 Environmental Hazards
Do not apply directly to water, to areas where surface water is present or to intertidal areas below the mean high water mark. Do not contaminate water when cleaning equipment or disposing of equipment washwaters.
3.3 Physical or Chemical Hazards
Spray solutions of this product can be mixed, stored and applied using only stainlesssteel, fiberglass, plastic or plastic-lined steel containers.
DO NOT MIX, STORE OR APPLY THIS PRODUCT OR SPRAY SOLUTIONS OF THIS PRODUCT IN GALVANIZED STEEL OR UNLINED STEEL (EXCEPT STAINLESS STEEL) CONTAINERS OR SPRAY TANKS. This product or spray solutions of this product react with such containers and tanks to produce hydrogen gas which may form a highly combustible gas mixture. This gas mixture could flash or explode, causing serious personal injury, if ignited by open flame, spark, welder’s torch, lighted cigarette or other ignition source.
-
DIRECTIONS FOR USE
It is a violation of Federal law to use this product in any manner inconsistent with its labeling. This product can only be used in accordance with the Directions for Use on this label or in separately published Monsanto supplemental labeling. Supplemental labeling can be found on the Internet at www.agrian.com, www.cdms.net or www.greenbook.net, or obtained from your Authorized Monsanto Retailer or Monsanto Company Representative.
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulations.
arising from unattached underground rhizomes or rootstocks of perennials that have not yet emerged at the time of application will not be affected by this herbicide and will continue to grow.
Maximum Application Rates: The maximum application or use rates stated throughout this label are given in units of volume (fluid ounces or quarts) of this product per acre. However, the maximum allowed application rates apply to this product combined with the use of any and all other herbicides containing the active ingredient glyphosate, whether applied separately or as tank mixtures, on a basis of total pounds of glyphosate (acid equivalents) per acre. If more than one glyphosate-containing product is applied to the same site within the same year, you must ensure that the total use of glyphosate (pounds acid equivalents) does not exceed the maximum allowed. The combined total of all treatments must not exceed 7 quarts of this product (8 pounds of glyphosate acid) per acre per year. See the INGREDIENTS section of this label for necessary product information.
ATTENTION
AVOID CONTACT OF HERBICIDE WITH FOLIAGE, STEMS, EXPOSED NON-WOODY ROOTS OR FRUIT OF CROPS, DESIRABLE PLANTS AND TREES, BECAUSE SEVERE INJURY OR DESTRUCTION MAY RESULT.
AVOID DRIFT. EXTREME CARE MUST BE USED WHEN APPLYING THIS PRODUCT TO PREVENT INJURY TO DESIRABLE PLANTS AND CROPS.
Do not allow the herbicide solution to mist, drip, drift or splash onto desirable vegetation since minute quantities of this product can cause severe damage or destruction to the crop, plants or other areas on which treatment was not intended. The likelihood of injury occurring from the use of this product increases when winds are gusty, as wind velocity increases, when wind direction is constantly changing or when there are other meteorological conditions that favor spray drift. When spraying, avoid combinations of pressure and nozzle type that will result in splatter or fine particles (mist) that are likely to drift. AVOID APPLYING AT EXCESSIVE SPEED OR PRESSURE.
NOTE: Use of this product in any manner not consistent with this label may result in injury to persons, animals or crops, or have other unintended consequences.
5.1 Weed Resistance Management
Glyphosate, the active ingredient in this product, is a Group 9 herbicide based on the mode of action classification system of the Weed Science Society of America. Any weed population may contain plants naturally resistant to Group 9 herbicides. Weed species resistant to Group 9 herbicides may be effectively managed utilizing another herbicide from a different Group or using other cultural or mechanical practices.
To minimize the occurrence of glyphosate-resistant biotypes observe the following general weed management recommendations:
• Scout your application site before and after herbicides applications.
• Control weeds early when they are relatively small.
-
Incorporate other herbicides and cultural or mechanical practices as part of your weed control system where appropriate.
-
Utilize the labeled rate for the most difficult weed in the site. Avoid tank-mixtures with other herbicides that reduce this product’s efficacy (through antagonism) or tank mixture recommendations which encourage rates of this product below the labeled rate.
-
Control weed escapes and prevent weeds from setting seeds.
-
Clean equipment before moving from site to site to minimize spread of weed seed.
-
Use new commercial seed as free of weed seed as possible.
-
Report any incidence of repeated non-performance of this product on a particular weed to your Monsanto representative, local retailer, or county extension agent.
5.2 Management Recommendations for Glyphosate-Resistant Weed Biotypes
NOTE: Appropriate testing is critical in order to confirm weed resistance to glyphosate. Call 1-800-ROUNDUP (1-800-768-6387) or contact your Monsanto representative to determine if resistance in any particular weed biotype has been confirmed in your area, or visit on the Internet www.weedresistancemanagement.com or www.weedscience.org.
Directions for the control of biotypes confirmed to be resistant to glyphosate are made available on separately published supplemental labeling or Fact Sheets for this product and may be obtained from your local retailer or Monsanto representative.
Since the occurrence of new glyphosate-resistant weeds cannot be determined until after product use and scientific confirmation, Monsanto Company is not responsible for any losses that may result from the failure of this product to control glyphosate-resistant weed biotypes.
The following good weed management practices are recommended to reduce the spread of confirmed glyphosate-resistant biotypes:
-
If a naturally occurring resistant biotype is present at your site, this product may be tank-mixed or applied sequentially with an appropriately labeled herbicide with a different mode of action to achieve control.
-
Cultural and mechanical control practices may also be used as appropriate.
-
Scout treated sites after herbicide applications and control escapes, including resistant biotypes, before they set seed.
-
Thoroughly clean equipment before leaving sites known to contain resistant biotypes.
Agricultural Use Requirements
Use this product only in accordance with its labeling and with the Worker Protection Standard, 40 CFR Part 170. This Standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about personal protective equipment (PPE) and restricted-entry interval. The requirements in this box only apply to uses of this product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted-entry interval (REI) of 4 hours.
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: coveralls, shoes plus socks and chemical-resistant gloves made of any waterproof material.
Non-Agricultural Use Requirements
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies when this product is used to produce agricultural plants on farms, forests, nurseries or greenhouses.
Keep people and pets off treated areas until spray solution has dried.
4.0 STORAGE AND DISPOSAL
Proper pesticide storage and disposal are essential to protect against exposure to people and the environment due to leaks and spills, excess product or waste, and vandalism. Do not allow this product to contaminate water, foodstuffs, feed or seed by storage and disposal.
PESTICIDE STORAGE: Store pesticides away from food, pet food, feed, seed, fertilizers, and veterinary supplies. Keep container closed to prevent spills and contamination.
PESTICIDE DISPOSAL: To avoid wastes, use all material in this container, including rinsate, by application according to label directions. If wastes cannot be avoided, offer remaining product to a waste disposal facility or pesticide disposal program. Such programs are often run by state or local governments or by industry. All disposal must be in accordance with applicable Federal, state and local regulations and procedures.
CONTAINER HANDLING AND DISPOSAL: See container label for container handling and disposal instructions and refilling limitations.
2
5.0 PRODUCT INFORMATION
Product Description: This product is a postemergence, systemic herbicide with no soil residual activity. It gives broad-spectrum control of many annual weeds, perennial weeds, woody brush and trees. It is formulated as a water-soluble liquid containing surfactant and no additional surfactant is needed or recommended.
Time to Symptoms: This product moves through the plant from the point of foliage contact to and into the root system. Visible effects are a gradual wilting and yellowing of the plant, which advances to complete browning of aboveground growth and deterioration of underground plant parts. Effects are visible on most annual weeds within 2 to 4 days, but on most perennial weeds, effects may not be visible for 7 or more days. Extremely cool or cloudy weather following treatment may slow activity of this product and delay development of visual symptoms.
Stage of Weeds: Annual weeds are easiest to control when they are small. Best control of most perennial weeds is obtained when treatment is made at late growth stages approaching maturity.
Mode of Action in Plants: The active ingredient in this product inhibits an enzyme found only in plants and microorganisms that is essential to the formation of specific amino acids.
Cultural Considerations: Reduced control may result when applications are made to annual or perennial weeds that have been mowed, grazed or cut, and have not been allowed to regrow to the specified stage for treatment.
Rainfastness: Heavy rainfall soon after application may wash this product off of the foliage and a repeat application may be required for adequate weed control.
No Soil Activity: Weeds must be emerged at the time of application to be controlled by this product. Weeds germinating from seed after application will not be controlled. Plants
-
Spray solutions of this product can be mixed, stored and applied using only clean stainless steel, fiberglass, plastic or plastic-lined steel containers. Clean sprayer parts immediately after using this product by thoroughly flushing with water.
Use caution to avoid siphoning back into the carrier source. Use approved anti-back- siphoning devices where required by State or local regulations.
6.1 Mixing with Water
NOTE: PRODUCT PERFORMANCE MAY BE SIGNIFICANTLY REDUCED IF WATER CONTAINING SOIL SEDIMENT IS USED AS CARRIER. DO NOT MIX THIS PRODUCT WITH WATER FROM PONDS AND DITCHES THAT IS VISIBLY MUDDY OR MURKY.
This product mixes readily with water. Mix spray solutions of this product as follows: Begin filling the mixing tank or spray tank with clean water. Add the proper amount of this product near the end of the filling process and mix gently. During mixing and application, foaming of the spray solution may occur. To prevent or minimize foaming, mix gently, terminate by-pass and return lines at the bottom of the tank and, if necessary, use an anti-foam or defoaming agent.
6.2 Tank Mixing
This product does not provide residual weed control. This product may be tank-mixed with other herbicides to provide residual weed control, a broader weed control spectrum or an alternate mode of action. Read and carefully observe the cautionary statements and all other information appearing on the labels of all herbicides used. Use according to the most restrictive precautionary statements for each product in the mixture.
When this label lists a tank mixture with a generic active ingredient such as atrazine, 2,4-D, dicamba, diuron or pendimethalin the user is responsible for ensuring that the specific application being made is included on the label of the specific product being used in the tank mixture. Refer to all individual product labels, supplemental labeling and fact sheets for all products in the tank mixture, and observe all precautions and limitations on the label, including application timing restrictions, soil restrictions and use according to the most restrictive precautionary statements for each product in the tank mixture.
Always predetermine the compatibility of all tank-mix products together in the carrier by mixing small proportional quantities in advance.
Buyer and all users are responsible for all loss or damage in connection with the use or handling of mixtures of this product with herbicides or other materials that are not expressed in this label. Mixing this product with herbicides or other materials not on this label may result in reduced performance.
6.3 Tank Mixing Procedure
When tank mixing, read and carefully observe label directions, cautionary statements and all information on the labels of all products used. Add the tank-mix product to the tank as directed by the label. Maintain agitation and add the specified amount of this product.
Maintain good agitation at all times until the contents of the tank are sprayed. If the spray mixture is allowed to settle, thorough agitation may be required to resuspend the mixture before spraying is resumed.
Keep by-pass line on or near the bottom of the tank to minimize foaming. Screen size in nozzle or line strainers should be no finer than 50-mesh.
Always predetermine the compatibility of labeled tank mixtures of this product with water carrier by mixing small proportional quantities in advance. Ensure that the specific tank mixture product is registered for application at the desired site.
Refer to the Tank Mixing and PRODUCT INFORMATION sections for additional precautions.
6.4 Mixing for Hand-Held Sprayers
Prepare the desired spray volume by mixing the amount of this product indicated in the
Desired volume:
1 gal 25 gal 100 gal
0.5 oz 0.8 pt 1.6 qt
1 oz 0.7 qt 2.8 qt
1.3 oz 1 qt 1 gal
2 oz 1.5 qt 1.5 gal
5 oz 4 qt 4 gal
For use in backpack, knapsack or pump-up sprayers, add the appropriate amount of this product, mixed with water in a larger container and then filling sprayer with the mixed solution.
Colorants or marking dyes may be added to spray solutions of this product; however, they can reduce product performance, especially at lower rates or dilution. Use colorants or dyes according to the manufacturer’s directions.Colorants or marking dyes may be added to spray solutions of this product; however, they can reduce product performance, especially at lower rates or dilution. Use colorants or dyes according to the manufacturer’s directions.
7.0 APPLICATION EQUIPMENT AND TECHNIQUES
Do not apply this product through any type of irrigation system.
2 tablespoons = 1 fluid ounce
Desired volume: 1 gal - mix 1.3oz for 1% solution, 2oz= 1.5%, 5oz= 4%, 9oz= 7%
Desired volume: 25 gal - mix .7qt for 1.5% solution, 1.5qt= 1.5%, 4qt= 4%, 7qt= 7%
For use in backpack, knapsack or pump-up sprayers, add the appropriate amount of this product, mixed with water in a larger container and then filling sprayer with the mixed solution.
3
7.1 Aerial Equipment
DO NOT APPLY THIS PRODUCT USING AERIAL SPRAY EQUIPMENT EXCEPT UNDER CONDITIONS AS SPECIFIED WITHIN THIS LABEL.
FOR AERIAL APPLICATION IN CALIFORNIA, REFER TO THE FEDERAL SUPPLEMENTAL LABEL FOR AERIAL APPLICATIONS IN THAT STATE FOR SPECIFIC INSTRUCTIONS, RESTRICTIONS AND REQUIREMENTS.
AVOID DRIFT. DO NOT APPLY WHEN WINDS ARE GUSTY OR UNDER ANY OTHER CONDITION WHICH FAVORS DRIFT. DRIFT MAY CAUSE DAMAGE TO ANY VEGETATION CONTACTED TO WHICH TREATMENT IS NOT INTENDED. TO PREVENT INJURY TO ADJACENT DESIRABLE VEGETATION, APPROPRIATE BUFFER ZONES MUST BE MAINTAINED.
Avoid direct application to any body of water.
Use the labeled rates of this herbicide in 3 to 25 gallons of water per acre unless otherwise specified on this label, or in separate supplemental labeling or fact sheets published by Monsanto for this product.
Coarse sprays are less likely to drift; therefore, do not use nozzles or nozzle configurations that dispense spray as fine spray droplets. Do not angle nozzles forward into the airstream and do not increase spray volume by increasing nozzle pressure. Drift control additives may be used. When a drift control additive is used, read and carefully observe the cautionary statements and all other information appearing on the additive label.
Ensure uniform application. To avoid streaked, uneven or overlapped application, use appropriate marking devices.
Aircraft Maintenance: Thoroughly wash aircraft, especially landing gear, after each day of spraying to remove residues of this product accumulated during spraying or from spills. PROLONGED EXPOSURE OF THIS PRODUCT TO UNCOATED STEEL SURFACES MAY RESULT IN CORROSION AND POSSIBLE FAILURE OF THE PART. LANDING GEAR IS MOST SUSCEPTIBLE. Maintaining an organic coating (paint) that meets aerospace specification MIL-C-38413 may prevent corrosion.
SPRAY DRIFT MANAGEMENT
AVOID DRIFT. EXTREME CARE MUST BE USED WHEN APPLYING THIS PRODUCT TO PREVENT INJURY TO DESIRABLE PLANTS AND CROPS.
Do not allow the herbicide solution to mist, drip, drift or splash onto desirable vegetation since minute quantities of this product can cause severe damage or destruction to the crop, plants or other areas on which treatment was not intended.
Avoiding spray drift at the application site is the responsibility of the applicator. The interaction of many equipment- and weather-related factors determines the potential for spray drift. The applicator and the grower are responsible for considering all these factors when making decisions.
AERIAL SPRAY DRIFT MANAGEMENT
The following drift management requirements must be followed to avoid off-target drift movement from aerial application.
1. The distance of the outermost nozzles on the boom must not exceed 3/4 the length of the wingspan or rotor.
2. Nozzles must always point backward, parallel with the air stream and never be pointed downwards more than 45 degrees. Where states have more stringent regulations, they should be observed.
Importance of Droplet Size
The most effective way to reduce drift potential is to apply large droplets. The best drift management strategy is to apply the largest droplets that provide sufficient coverage and control. Applying larger droplets reduces drift potential, but will not prevent drift if applications are made improperly, or under unfavorable environmental conditions (see the “Wind”, “Temperature and Humidity”, and “Temperature Inversions” sections of this label).
Controlling Droplet Size
•Volume: Use high flow rate nozzles to apply the highest practical spray volume. Nozzles
with the higher rated flows produce larger droplets.
•Pressure: Use the lower spray pressures recommended for the nozzle. Higher pressure reduces droplet size and does not improve canopy penetration. When higher flow rates are needed, use higher flow rate nozzles instead of increasing pressure.
•Number of nozzles: Use the minimum number of nozzles that provide uniform coverage.
•Nozzle orientation: Orienting nozzles so that the spray is released backwards, parallel to the air stream, will produce larger droplets than other orientations. Significant deflection from the horizontal will reduce droplet size and increase drift potential.
APPLY SPRAY SOLUTIONS IN PROPERLY MAINTAINED AND CALIBRATED EQUIPMENT APABLE OF DELIVERING DESIRED VOLUMES.
•Nozzle type: Use a nozzle type that is designed for the intended application. With most nozzle types, narrower spray angles produce larger droplets. Consider using low-drift nozzles. Solid stream nozzles oriented straight back produce larger droplets than other nozzle types.
•Boom length: For some use patterns, reducing the effective boom length to less than 3/4 of the wingspan or rotor length may further reduce drift without reducing swath width.
•Application height: Applications must not be made at a height greater than 10 feet above the top of the largest plants unless a greater height is required for aircraft safety. Making applications at the lowest height that is safe reduces the exposure of the droplets to evaporation and wind.
Swath Adjustment
When applications are made with a crosswind, the swath will be displaced downwind. Therefore, on the up and downwind edges of the field, the applicator must compensate for this displacement by adjusting the path of the aircraft upwind. Swath adjustment distance should increase with increasing drift potential (higher wind speed, smaller droplets, etc.).
Wind
Drift potential is lowest between wind speeds of 2 to 10 miles per hour. However, many factors, including droplet size and equipment type determine drift potential at any given speed. Application must be avoided below 2 miles per hour due to variable wind direction and high inversion potential. NOTE: Local terrain can influence wind patterns. Every applicator needs to be familiar with local wind patterns and how they affect drift.
Temperature and Humidity
When making applications in low relative humidity, setup equipment to produce larger droplets to compensate for evaporation. Droplet evaporation is most severe when conditions are both hot and dry.
Temperature Inversions
Applications must not be made during a temperature inversion because drift potential is high. Temperature inversions restrict vertical air mixing, which causes small, suspended droplets to remain in a concentrated cloud. This cloud can move in unpredictable directions due to the light variable winds common during inversions. Temperature inversions are characterized by increasing temperatures with altitude and are common on nights with limited cloud cover and light to no wind. They begin to form as the sun sets and often continue into the morning. Their presence can be indicated by ground fog; however, if fog is not present, the movement of smoke from a ground source or an aircraft smoke generator can also identify temperature inversions. Smoke that layers and moves laterally in a concentrated cloud (under low wind conditions) indicates an inversion, while smoke that moves upward and rapidly dissipates indicates good vertical air mixing.
Sensitive Areas
Apply this product when the potential for drift to adjacent sensitive areas (e.g., residential areas, bodies of water, known habitat for threatened or endangered species, non-target crops) is minimal (e.g., when wind is blowing away from the sensitive areas).
7.2 Ground Broadcast Equipment
Apply the labeled rates of this product in 3 to 40 gallons of water per acre as a broadcast
spray unless otherwise specified on this label, or in separate supplemental labeling or fact sheets published by Monsanto for this product. As density of weeds increases, spray volume should be increased within the specified range to ensure complete coverage. Carefully select proper nozzles to avoid spraying a fine mist. For best results with ground application equipment, use flat-fan nozzles. Check spray pattern for uniform distribution of spray droplets.
7.3 Hand-Held or Backpack Equipment
Apply to foliage of vegetation to be controlled. For applications made on a spray-to-wet basis, spray coverage should be uniform and complete. Do not spray to the point of runoff. Use coarse sprays only.
For low-volume directed spray applications, spray coverage should be uniform with at least 50 percent of the foliage contacted. Coverage of the top one-half of the plant is important for best results. To ensure adequate spray coverage, spray both sides of large or tall woody brush and trees, when foliage is thick and dense, or where there are multiple sprouts.
7.4 Selective Equipment
This product may be diluted in water and applied through shielded applicators, hooded sprayers, wiper applicators or sponge bars to weeds listed on this label growing in any non-crop site specified on this label.
AVOID CONTACT OF HERBICIDE WITH DESIRABLE VEGETATION, AS SERIOUS INJURY OR DEATH OF THE DESIRABLE VEGETATION IS LIKELY TO OCCUR.
Application equipment used above desired vegetation should be adjusted so that the lowest spray stream or wiper contact point is at least 2 inches above the desirable vegetation. Droplets, mist, foam or splatter of the herbicide solution settling on desirable vegetation is likely to result in discoloration, stunting or destruction.
Better results may be obtained when more of the weed is exposed to the herbicide solution. Weeds not contacted by the herbicide solution will not be affected. This may
occur in dense clumps, severe infestations or when the height of the weeds varies so that not all weeds are contacted. In these instances, repeat treatment may be necessary.
Shielded and Hooded Applicators
A shielded or hooded applicator directs the herbicide solution onto weeds, while shielding desirable vegetation from the herbicide. Use nozzles that provide uniform coverage within the treated area. Keep shields on these sprayers adjusted to protect desirable vegetation. EXTREME CARE MUST BE EXERCISED TO AVOID CONTACT OF HERBICIDE WITH DESIRABLE VEGETATION.
Wiper Applicators
Wiper applicators are devices that physically wipe the appropriate amounts of this product directly onto the weed. Equipment must be designed, maintained and operated to prevent the herbicide solution from contacting desirable vegetation.
Application equipment used over the top of desirable vegetation should be adjusted so that the wiper contact point is at least 2 inches above the desirable vegetation. Better results may be obtained when more of the weed is exposed to the herbicide solution. Weeds should be a minimum of 6 inches above the desirable vegetation. Adjust the height of the applicator to ensure adequate contact with weeds. Weeds not contacted by the herbicide solution will not be affected. Poor contact may occur when weeds are growing in dense clumps, in severe weed infestations or when weed height varies dramatically. In these instances, repeat treatments may be necessary.
Operate this equipment at ground speeds no greater than 5 miles per hour. Performance may be improved by reducing speed in areas of heavy weed infestations to provide adequate wiper saturation with the herbicide solution. Better results may be obtained when two applications are made in opposite directions.
Droplets, mist, foam or splatter of the herbicide solution settling onto desirable vegetation may result in discoloration, stunting or destruction. Avoid leakage or dripping onto desirable vegetation. Keep wiping surfaces clean. Be aware that on sloping ground the herbicide solution may migrate, causing dripping on the lower end and drying of the wicks on the upper end of the wiper applicator.
Do not use wiper applicators when weeds are wet.
Mix only the amount of this product to be used during a 1-day period, as reduced product performance may result from the use of solutions held in storage. Clean wiper parts immediately after using this product by thoroughly flushing with water.
For Rope or Sponge Wick Applicators—Solutions ranging from 25 to 70 percent of this product in water may be used.
For Panel Applicators and Pressure-Feed Systems—Solutions ranging from 25 to 100 percent of this product in water may be used.
When applied as directed, this product CONTROLS the following weeds:
Corn, volunteer, sicklepod
Panicum, Texas Rye, common Shattercane
Sicklepod Spanishneedles Starbur, bristly
When applied as directed, this product SUPPRESSES the following weeds:
Beggarweed, Florida Bermudagrass Dogbane, hemp Dogfennel Guineagrass Johnsongrass Milkweed Nightshade, silverleaf Pigweed, redroot
7.5 Injection Systems
This product may be used in aerial or ground injection spray systems. It may be used as a liquid concentrate or diluted prior to injecting into the spray stream. Do not mix this product with the undiluted concentrate of other products when using injection systems unless specifically instructed in this label.
7.6 CDA Equipment
The rate of this product applied per acre by controlled droplet application (CDA) equipment must not be less than the amount directed in this label when applied by conventional broadcast equipment. For vehicle-mounted CDA equipment, apply 2 to 15 gallons of water per acre.
CDA equipment produces a spray pattern that is not easily visible. Extreme care must be exercised to avoid spray or drift contacting the foliage or any other green tissue of desirable vegetation, as damage or destruction is likely to result.
Ragweed, common Ragweed, giant Smutgrass Sunflower
Thistle, Canada Thistle, musk Vaseygrass Velvetleaf
THIS LABEL INFORMATION IS A PARTIAL REPRESENTATION OF THE COMPLETE LABEL. FOR COMPLETE LABEL INSTRUCTIONS OR MSDS PLEASE CONTACT SUPPLIER.
PRODUCT REVIEWS
RELATED PRODUCTS
Roundup, PowerMAX 3 Herbicide, 2.5 gal
$169.99
11 in stock in Pasco
Buy
Online,
Pickup in Store
Buy
Online,
Ship to Home
Trimec Classic Broadleaf Herbicide
$99.99 - $199.00
In stock, see options for availability
Buy
Online,
Pickup in Store
2, 4-D Amine 4
$39.99 - $69.99
In stock, see options for availability
Buy
Online,
Pickup in Store
Crossbow Herbicide Weed & Brush Killer
$26.99 - $179.99
In stock, see options for availability
Buy
Online,
Pickup in Store
