Snapshot 2.5 TG Pre-emergent Herbicide, 50 lb
- Selective pre-emergent herbicide
- Controls wide range of annual grasses and broadleaf weeds
- Can be applied in early spring, late summer to early fall or immediately after cultivation
- Won’t move out of the application zone
- Rate of use: 2.30-4.6 lbs. per 1000 sq. ft.
$179.99
Select options to see availability at your location
Your pick up store is {{selectedStoreCity}}
{{formatStockMessage(selectedStoreQty, userStoreStock.price).message}}
This item cannot be sold in this state.
+ Check nearest locations with stock available
Stores selection based on detection of your zip code as {{wg.zipcode}}
Snapshot is a selective pre-emergent herbicide that provides control of listed annual grasses and broadleaf weeds in landscape ornamentals, ground covers, perennials, non-bearing fruit and nut trees, container grown ornamentals, non-bearing vineyards, field-grown ornamentals and non-cropland.
This item cannot be sold in the following states: California, California
| Weight | 50 lbs |
|---|
A selective preemergence herbicide for control of certain broadleaf weeds and annual grasses in:
Environmental Hazards
This pesticide is extremely toxic to freshwater marine, and estuarine
fish and aquatic invertebrates including shrimp and oyster. Do not apply
directly to water, or to areas where surface water is present or to intertidal
areas below the mean high water mark. Do not apply in a manner which
will directly expose canals, lakes, streams, ponds, marshes or estuaries
to aerial drift. Do not contaminate water when cleaning equipment or
disposing of equipment washwaters.
Directions for Use
It is a violation of Federal law to use this product in a manner inconsistent
with its labeling.
Read all Directions for Use carefully before applying.
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your state or tribe, consult the agency responsible for pesticide regulation.
• Landscape Ornamentals • Christmas Tree
Plantations
• Container Grown
Ornamentals
• Field Grown Ornamentals
• Groundcovers/Perennials • Non-Bearing Fruit and
Nut Trees
• Non-Bearing Vineyards
• Non-Cropland
Active Ingredients:
trifluralin: a,a,a-trifluoro-2,6-dinitro-N,
N-dipropyl-p-toluidine .................................................................. 2.0% isoxaben: N-[3-(1-ethyl-1-methylpropyl)-5-
isoxazolyl]-2,6-dimethoxybenzamide
and isomers.................................................................................. 0.5% Other Ingredients ............................................................................... 97.5% Total ................................................................................................. 100.0%
Contains 1.25 lb active ingredient per 50 lb bag.
Precautionary Statements
Hazards to Humans and Domestic Animals
EPA Reg. No. 62719-175
CAUTION
Causes Moderate Eye Irritation • Harmful If Swallowed Or Inhaled • Prolonged Or Frequently Repeated Skin Contact May Cause Allergic Reaction In Some Individuals
Avoid breathing dust or spray mist and contact with eyes or clothing. Wash thoroughly with soap and water after handling.
Personal Protective Equipment (PPE)
Applicators and other handlers must wear:
• Long-sleeved shirt and long pants
• Shoes plus socks
Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry.
Engineering Controls
When handlers use closed systems or enclosed cabs in a manner that meets the requirements listed in the Worker Protection Standard (WPS) for agricultural pesticides [40 CFR 170.240 (d) (4-6)], the handler PPE requirements may be reduced or modified as specified in the WPS.
Agricultural Use Requirements
Use this product only in accordance with its labeling and with the
Worker Protection Standard, 40 CFR Part 170. This Standard contains
requirements for the protection of agricultural workers on farms, forests,
nurseries, and greenhouses, and handlers of agricultural pesticides.
It contains requirements for training, decontamination, notification,
and emergency assistance. It also contains specific instructions and
exceptions pertaining to the statements of this label about personal
protective equipment (PPE), and restricted entry interval. The
requirements in the box only apply to uses of this product that are
covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 12 hours.
PPE required for early entry to treated areas that is permitted under the
Worker Protection Standard and that involves contact with anything that
has been treated, such as plants, soil, or water, is:
• Coveralls
• Waterproof gloves • Shoes plus socks
Non-Agricultural Use Requirements
The requirements of this box apply to uses of this product that are NOT
within the scope of the Worker Protection Standard for agricultural
pesticides (40 CFR Part 170). The WPS applies when this product
is used to produce agricultural plants on farms, forests, nurseries, or
greenhouses.
For applications in landscape settings and in non-cropland sites, do not enter or allow others to enter the treated area until dusts have settled.
Storage and Disposal
Do not contaminate water, food, or feed by storage or disposal.
Pesticide Storage: Store in original container only. In case of spill,
contain material and dispose as waste.
Pesticide Disposal: Wastes resulting from the use of this product may
be disposed of on site or at an approved waste disposal facility.
Nonrefillable rigid containers 5 gallons or less:
Container Handling: Nonrefillable container. Do not reuse or refill this
container.
Triple rinse or pressure rinse container (or equivalent) promptly after
emptying. Triple rinse as follows: Empty the remaining contents into
application equipment or a mix tank and drain for 10 seconds after
the flow begins to drip. Fill the container 1/4 full with water and recap.
Shake for 10 seconds. Pour rinsate into application equipment or a
mix tank or store rinsate for later use or disposal. Drain for 10 seconds
after the flow begins to drip. Repeat this procedure two more times.
User Safety Recommendations
Users should:
-
Wash hands before eating, drinking, chewing gum, using tobacco, or
using the toilet.
-
Remove clothing immediately if pesticide gets inside. Then wash
thoroughly and put on clean clothing.
-
Users should remove PPE immediately after handling this product.
As soon as possible, wash thoroughly and change into clean clothing.
Pressure rinse as follows: Empty the remaining contents into application
equipment or a mix tank and continue to drain for 10 seconds after
the flow begins to drip. Hold container upside down over application
equipment or mix tank or collect rinsate for later use or disposal. Insert
pressure rinsing nozzle in the side of the container, and rinse at about
40 psi for at least 30 seconds. Drain for 10 seconds after the flow begins
to drip. Then offer for recycling if available or puncture and dispose of in
a sanitary landfill, or by incineration, or by other procedures allowed by
state and local authorities.
Nonrefillable nonrigid containers:
Container Handling: Nonrefillable container. Do not reuse or refill
this container. Completely empty bag into application equipment.
Then offer for recycling if available, or dispose of in a sanitary landfill,
or by incineration, or by other procedures allowed by state and local
authorities.
Refillable rigid containers larger than 5 gal:
Container Handling: Refillable container. Refill this container with
pesticide only. Do not reuse this container for any other purpose.
Cleaning the container before final disposal is the responsibility of
the person disposing of the container. Cleaning before refilling is the
responsibility of the refiller. To clean the container before final disposal,
empty the remaining contents from this container into application
equipment or a mix tank. Fill the container about 10% full with water
and, if possible, spray all sides while adding water. If practical, agitate
vigorously or recirculate water with the pump for two minutes. Pour
or pump rinsate into application equipment or rinsate collection
system. Repeat this rinsing procedure two more times. Then offer for
recycling if available, or puncture and dispose of in a sanitary landfill,
or by incineration, or by other procedures allowed by state and local
authorities.
Nonrefillable rigid containers larger than 5 gal:
Container Handling: Nonrefillable container. Do not reuse or refill this
container.
Triple rinse or pressure rinse container (or equivalent) promptly after
emptying. Triple rinse as follows: Empty the remaining contents into
application equipment or a mix tank. Fill the container 1/4 full with
water. Replace and tighten closures. Tip container on its side and
roll it back and forth, ensuring at least one complete revolution, for
30 seconds. Stand the container on its end and tip it back and forth
several times. Turn the container over onto its other end and tip it back
and forth several times. Empty the rinsate into application equipment
or a mix tank or store rinsate for later use or disposal. Repeat this
procedure two more times. Pressure rinse as follows: Empty the
remaining contents into application equipment or a mix tank and
continue to drain for 10 seconds after the flow begins to drip. Hold
container upside down over application equipment or mix tank or collect
rinsate for later use or disposal. Insert pressure rinsing nozzle in the
side of the container, and rinse at about 40 psi for at least 30 seconds.
Drain for 10 seconds after the flow begins to drip. Then offer for
recycling if available, or puncture and dispose of in a sanitary landfill, or by incineration, or by other procedures allowed by state and local
authorities.
General Information
Snapshot® DG specialty herbicide is a pre-emergence product for control
of certain broadleaf weeds and annual grasses in container and landscape
ornamentals, nursery stock, Christmas trees, ground covers/perennials,
non-bearing fruit and nut trees, non-bearing vineyards and non-cropland
areas. Apply Snapshot DG anytime prior to germination of target weeds,
or immediately after cultivation. Length of weed control will vary with
rate of Snapshot DG applied, weed population, potting media or soil
conditions, temperature, watering regime, and other factors. Following
application, user should monitor and observe level of weed control over
time to determine when additional applications may be needed.
General Use Precautions and Restrictions
In Arizona: The state of Arizona has not approved Snapshot DG for use on plants grown for agricultural/commercial production; such as on Christmas tree plantations, container grown or field grown ornamentals, non-bearing fruit and nut trees and non-bearing vineyards.
Snapshot DG controls weeds growing from seed. Snapshot DG does
not control established weeds, weeds growing from stolons, rhizomes,
or root pieces. Existing weeds should be controlled by cultivation or with
post-emergence herbicides. Weed residues, prunings and trash should
be removed or thoroughly mixed into soil prior to treatment. Soil should
be in good condition and free of clods at the time of application. A single
rainfall or sprinkler irrigation of 0.5 inches or more, or flood irrigation is
required to activate Snapshot DG. Optimum weed control is obtained when Snapshot DG is activated within 3 days of application. If rainfall
or irrigation does not occur within 3 days of application and tillage is
possible, Snapshot DG may be activated using cultivation equipment
capable of uniformly mixing the herbicide into the upper 1 to 2 inches
of soil. Failure to activate Snapshot DG within 3 days of application
may result in erratic control of annual grasses. Do not apply when wind
conditions favor drift of Snapshot DG granules from the target area.
Repeat applications at 150 lb per acre and higher should not be made sooner than 60 days after a previous application of Snapshot DG. Do not apply over 600 pounds per acre total of Snapshot DG within a 12-month period.
Tolerance of Turfgrass Adjacent to Ornamental Plantings: Accidental application to turf may occur when applying Snapshot DG to ornamental plantings. Snapshot DG is not recommended for weed control in turfgrasses, but turfgrasses are generally tolerant to small amounts of this product that fall outside of the intended area of application.
Do not aerially apply Snapshot DG.
Treatment Species Not Listed on the Label for Snapshot DG
Users who wish to use Snapshot DG on plant species not recommended on this label may determine the suitability for use by treating a small number of such plants at a recommended rate. Prior to treatment of larger areas, the treated plants should be observed for any sign of herbicidal injury for during 30 to 60 days of normal growing conditions to determine if the treatment is safe to the target plant species. The user assumes responsibility for any plant damage or other liability resulting from use of Snapshot DG on plant species not recommended on this label.
Application Instructions
Apply Snapshot DG using a drop or rotary-type spreader designed to apply granular herbicides or insecticides. Calibrate application equipment prior to use according to manufacturer’s directions. Check frequently to be sure equipment is working properly and distributing granules uniformly. Do not use spreaders that apply material in narrow concentrated bands. Avoid skips or overlaps as poor weed control or crop injury may occur. More uniform application may be achieved by spreading half of the required amount of product over the area and then applying the remaining half in swaths at right angles to the first.
Application Techniques for Applying Snapshot DG
-
When using a drop-type spreader, a splashboard mounted under the hopper will provide more even granule distribution.
-
A chain fastened to the side of the spreader and allowed to drag on the soil surface can be used to mark the edge of the treated swath and help prevent skips or overlaps.
-
For treating smaller areas or rows of nursery stock or ornamental beds, a hand held or push-type rotary applicator such as a whirlybird or cyclone unit is recommended. For hand held units, walk and turn the crank at a constant rate of speed.
-
A shaker-type applicator made from a small container with holes punched in the bottom is recommended for small, difficult to treat areas. Carefully measure the amount of product needed to avoid over application.
-
The weight-to-volume conversion table below provides equivalent amounts of Snapshot DG.
Rate | Amount/1000 sq ft | Amount/100 sq ft | ||
lb/Acre | (lb) | (quarts) | (lb) | (cups) |
100 150 200 | 2.30 3.45 4.60 | 1.75 2.60 3.50 | 0.23 0.35 0.46 | 0.7 1.0 1.4 |
-
1 lb of Snapshot DG = 0.75 quart = 3 cups
Spreader Settings as a Guide for Calibration
Note: These settings are provided as a suggested starting point in calibrating each individual spreader. Since no two spreaders are alike, these settings are not intended to be used as absolute recommendations by Dow AgroSciences or the spreader manufacturer.
-
1 lb of Snapshot DG = 0.75 quart = 3 cups
Spreader Settings as a Guide for Calibration
Note: These settings are provided as a suggested starting point in calibrating each individual spreader. Since no two spreaders are alike, these settings are not intended to be used as absolute recommendations by Dow AgroSciences or the spreader manufacturer.
THIS IS A PARTIAL LABEL. FOR ENTIRE LABEL OR MSDS PLEASE CONTACT SUPPLIER OR PRODUCT CONTAINER. USE AS INSTRUCTED.
PRODUCT REVIEWS
RELATED PRODUCTS
Roundup, PowerMAX 3 Herbicide, 2.5 gal
{{ storePrice }}
{{ storeSpecialPrice }}
Add to Cart to See Pricing
In stock, see options for availability
{{storeQuantity}} in stock in {{wg.store.city}}
Limited stock in {{wg.store.city}} Check nearby stores
Out of stock in {{wg.store.city}} Check nearby stores
Not carried in {{wg.store.city}} Check nearby stores
Cannot be sold in {{wg.store.city}} Check nearby stores
This item is not available for purchase online.
Buy
Online,
Pickup in Store
Buy
Online,
Ship to Home
Eraser 41% Glyphosate with Surfactant Herbicide
{{ storePrice }}
{{ storeSpecialPrice }}
Add to Cart to See Pricing
In stock, see options for availability
{{storeQuantity}} in stock in {{wg.store.city}}
Limited stock in {{wg.store.city}} Check nearby stores
Out of stock in {{wg.store.city}} Check nearby stores
Not carried in {{wg.store.city}} Check nearby stores
Cannot be sold in {{wg.store.city}} Check nearby stores
This item is not available for purchase online.
Buy
Online,
Pickup in Store
Buy
Online,
Ship to Home
Trimec Classic Broadleaf Herbicide
{{ storePrice }}
{{ storeSpecialPrice }}
Add to Cart to See Pricing
In stock, see options for availability
{{storeQuantity}} in stock in {{wg.store.city}}
Limited stock in {{wg.store.city}} Check nearby stores
Out of stock in {{wg.store.city}} Check nearby stores
Not carried in {{wg.store.city}} Check nearby stores
Cannot be sold in {{wg.store.city}} Check nearby stores
This item is not available for purchase online.
Buy
Online,
Pickup in Store
Buy
Online,
Ship to Home
2, 4-D Amine 4
{{ storePrice }}
{{ storeSpecialPrice }}
Add to Cart to See Pricing
In stock, see options for availability
{{storeQuantity}} in stock in {{wg.store.city}}
Limited stock in {{wg.store.city}} Check nearby stores
Out of stock in {{wg.store.city}} Check nearby stores
Not carried in {{wg.store.city}} Check nearby stores
Cannot be sold in {{wg.store.city}} Check nearby stores
This item is not available for purchase online.
Buy
Online,
Pickup in Store
Buy
Online,
Ship to Home
